# Z Probe Settings

**URL:** <https://community.inventables.com/t/z-probe-settings/99765>\
**Category:** Uncategorized\
**Created:** [September 14, 2020, 12:29pm UTC](https://community.inventables.com/t/z-probe-settings/99765 "2020-09-14T12:29:57Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![RussellCrawford](https://avatars.discourse-cdn.com/v4/letter/r/958977/32.png) [@RussellCrawford](https://community.inventables.com/u/RussellCrawford)\
**Post date:** [September 14, 2020, 12:29pm UTC](https://community.inventables.com/t/z-probe-settings/99765/1 "2020-09-14T12:29:57Z")

</div>

Can I change the thickness of my Z probe? The one from Inventables measures .587", If I have one that measures 1.0", can I change that in the settings?  
Thank You  
Russell

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [September 14, 2020, 12:52pm UTC](https://community.inventables.com/t/z-probe-settings/99765/2 "2020-09-14T12:52:50Z")

</div>

Are you using Easel to control the machine, @RussellCrawford?  
If yes, see Phil’s answer below.

---

<div class="post-metadata">

**Author:** ![PhillipLunsford](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/philliplunsford/32/33614_2.png) [@PhillipLunsford](https://community.inventables.com/u/PhillipLunsford)\
**Post date:** [September 14, 2020, 4:59pm UTC](https://community.inventables.com/t/z-probe-settings/99765/3 "2020-09-14T16:59:19Z")

</div>

@RussellCrawford Yes you can. Go back to the machine setting up. Go through the steps and when you get to the probe it will ask you if you want to change settings or advanced. I can’t remember the exact question but it opens a window to change all the settings including the probe thickness.

---

<div class="post-metadata">

**Author:** ![RussellCrawford](https://avatars.discourse-cdn.com/v4/letter/r/958977/32.png) [@RussellCrawford](https://community.inventables.com/u/RussellCrawford)\
**Post date:** [September 14, 2020, 11:55pm UTC](https://community.inventables.com/t/z-probe-settings/99765/4 "2020-09-14T23:55:29Z")

</div>

Awesome, thanks Phillip and Neil. I think we are going to get lucky again Phillip, Sally is headed East towards Mississippi.  
I’m still using Easel. I purchased V-Carve and PicSender just need to install PicSender and figure it out.

---

<div class="post-metadata">

**Author:** ![PhillipLunsford](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/philliplunsford/32/33614_2.png) [@PhillipLunsford](https://community.inventables.com/u/PhillipLunsford)\
**Post date:** [September 15, 2020, 1:05am UTC](https://community.inventables.com/t/z-probe-settings/99765/5 "2020-09-15T01:05:44Z")

</div>

I’m using UGS and VCarve. Yes, I think you are right. Going East is good. Cat 2 sucks though for Mississippi