# X-carve accuracy Issues

**URL:** <https://community.inventables.com/t/x-carve-accuracy-issues/16568>\
**Category:** X-Carve\
**Created:** [November 29, 2015, 7:06pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568 "2015-11-29T19:06:34Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [November 29, 2015, 7:06pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/1 "2015-11-29T19:06:34Z")

</div>

Really struggling right now. No matter what I cut, my machine is consitently 0.5mm too big. Trying to just make 25mm x 25mm squares, 1mm deep. to test the accuracy

1000mm x 1000mm machine, Makita router dewalt in 2 weeks)

I’ve done everything I can think of:

Belt Tension  
V wheel adjustment  
Potentiality  
Different bits, measuring their diameter  
X- axis stiffening mod  
Squaring the machine  
Checking every screw on the machine  
Inside and outside profile cuts.  
Pocket cuts

I feel like there must be something really stupid i’m missing. It’s always right around 0.5mm too big. I just don’t get it.

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [November 29, 2015, 7:09pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/2 "2015-11-29T19:09:25Z")

</div>

Have you calibrated your steps per mm yet?

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [November 29, 2015, 7:19pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/3 "2015-11-29T19:19:09Z")

</div>

I did, and was then constantly told not too, so changed them back 🙂

---

<div class="post-metadata">

**Author:** ![Ebr](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/ebr/32/12389_2.png) [@Ebr](https://community.inventables.com/u/Ebr)\
**Post date:** [November 29, 2015, 7:37pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/4 "2015-11-29T19:37:29Z")

</div>

Reconsider changing steps/mm…

Well worth a try 😄

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [November 29, 2015, 7:42pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/5 "2015-11-29T19:42:07Z")

</div>

Each time the belts are changed in tightness, the steps per mm need to be calibrated if you are looking for accurate cuts.

Here is a video on how to do so:

Here’s another by @RobertA_Rieke

As a side note, if you move your gantry by hand then it will move out of square. Be sure that you only move the gantry with jog controls or if you have to move it by hand then re-square after each time.

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [November 29, 2015, 8:24pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/6 "2015-11-29T20:24:24Z")

</div>

I saw quite a long thread about the X carve accuracy. Everyone was changing the steps and at the end it was just set back to the default and it cleared up all their issues. Which is why I’m in two minds about it

---

<div class="post-metadata">

**Author:** ![Zach\_Kaplan](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/zach_kaplan/32/84268_2.png) [@Zach\_Kaplan](https://community.inventables.com/u/Zach_Kaplan)\
**Post date:** [November 29, 2015, 8:44pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/7 "2015-11-29T20:44:35Z")

</div>

Which software are you using?

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [November 29, 2015, 9:47pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/8 "2015-11-29T21:47:14Z")

</div>

Easel, solid works, cam bam, meshcam, mastercam, rhino. They’ve all made no difference on my outcome

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [November 29, 2015, 10:10pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/9 "2015-11-29T22:10:19Z")

</div>

Ok. You’ve tried all of the other steps that I’d recommend that you check. Calibration of steps per mm is the next thing to check. If you try it out (it isn’t very hard) you can always put it back if it doesn’t work.

Give it a try and see if it fixes the issue… what do you have to lose?

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [November 29, 2015, 10:14pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/10 "2015-11-29T22:14:33Z")

</div>

True! Just kinda sick of tweaking stuff in I just wanna cut haha

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [November 30, 2015, 8:13pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/11 "2015-11-30T20:13:09Z")

</div>

Calibrate the machine along its X (steps per mm). Still cutting too little on the X axis of a square. 25 mm square came out at 24.70 along its X.

---

<div class="post-metadata">

**Author:** ![BobMarinoff](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/bobmarinoff/32/73454_2.png) [@BobMarinoff](https://community.inventables.com/u/BobMarinoff)\
**Post date:** [November 30, 2015, 9:50pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/12 "2015-11-30T21:50:40Z")

</div>

Their is very,very good how to do the calibrate all check youtube look for calibrate X Carve

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [November 30, 2015, 9:52pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/13 "2015-11-30T21:52:35Z")

</div>

As was posted a few posts up the thread.

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [November 30, 2015, 9:55pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/14 "2015-11-30T21:55:10Z")

</div>

Can you give the details of this specific carve?

bit size  
depth per pass  
feeds/speeds  
material type

pics?

Do you get any type of chatter or different noise when milling in the X direction as opposed to the Y direction?

---

<div class="post-metadata">

**Author:** ![DavidSohlstrom](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/davidsohlstrom/32/77077_2.png) [@DavidSohlstrom](https://community.inventables.com/u/DavidSohlstrom)\
**Post date:** [November 30, 2015, 10:08pm UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/15 "2015-11-30T22:08:20Z")

</div>

If you don’t mind. Explain how you went about checking and calibrating your machine.

FYI When I calibrate a CNC machine I do it as follows.

Clamp a 123 block to the table, out close to the center of travel.  
Set up a dial test indicator on the carriage.  
Move the carriage so the indicator just touches the 123 block in the direction you want to test in. Zero the indicator.  
Now issue a move of 3 inches away from the 123 block.  
Now very carefully insert a second 123 block in the space between the indicator and the first 123 block.  
If you read zero then all is good. If not then you need to adjust your steps per unit until when you run the test again you get a zero reading.

This is the best way to check. You are not relying on eye sight on a ruler to see how far your machine is moving.  
As has been stated above if the tension on your belts is changed then you need to recheck because belt stretch will change things.

Hope this helps

Dave  
Ariel, WA

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [December 1, 2015, 12:32am UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/16 "2015-12-01T00:32:52Z")

</div>

I have no access to a dial indicator.

To calibrate the machine I fixed a machinist rule to the bed and followed the videos above.

Whilst jogging, the machine is ok.

V cutter, 0.2mm deep. Measured the width and used it as the cutter diameter.

My test shape

 ![](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/2X/8/8e504d6ae01937b507f1ef4d0e90bce35299e13d.jpeg)

---

<div class="post-metadata">

**Author:** ![DavidSohlstrom](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/davidsohlstrom/32/77077_2.png) [@DavidSohlstrom](https://community.inventables.com/u/DavidSohlstrom)\
**Post date:** [December 1, 2015, 12:42am UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/17 "2015-12-01T00:42:21Z")

</div>

Jamie

Today is your lucky day if you would like to get a test dial indicator and a set of 123 blocks.

Enco is having a 25% off and free shipping until 11 pm EST.

Use code CYBER for discount and MONDAY for free shipping.

I would changed to a 1/8" end mill. A small change in DOC (depth of cut) will change your results when using a V bit.

Dave  
Ariel, WA

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [December 1, 2015, 12:53am UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/18 "2015-12-01T00:53:52Z")

</div>

I concur. I’d switch to an end mill that will cut a straight side regardless of depth and remeasure.

---

<div class="post-metadata">

**Author:** ![JamiePhillips](https://avatars.discourse-cdn.com/v4/letter/j/b5a626/32.png) [@JamiePhillips](https://community.inventables.com/u/JamiePhillips)\
**Post date:** [December 1, 2015, 1:48am UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/19 "2015-12-01T01:48:38Z")

</div>

Oh I did plenty of tests with 1/8 and 1/4 also. Mainly 1/4" too reduce the chance of my reducer collet having an impact on the result. It was all 0.4mm out.

---

<div class="post-metadata">

**Author:** ![sketch42](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sketch42/32/76722_2.png) [@sketch42](https://community.inventables.com/u/sketch42)\
**Post date:** [December 1, 2015, 1:53am UTC](https://community.inventables.com/t/x-carve-accuracy-issues/16568/20 "2015-12-01T01:53:24Z")

</div>

So after calibration it was 0.4mm out consistently in both directions for the 1/4"? What was the actual measurement of the 1/4"? Mine comes in at 6.3mm

[Next page](https://community.inventables.com/t/x-carve-accuracy-issues/16568.md?page=2)
