# Vibration issues and loud noises!

**URL:** <https://community.inventables.com/t/vibration-issues-and-loud-noises/12535>\
**Category:** Troubleshooting\
**Created:** [August 29, 2015, 6:13pm UTC](https://community.inventables.com/t/vibration-issues-and-loud-noises/12535 "2015-08-29T18:13:50Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![WillEaly](https://avatars.discourse-cdn.com/v4/letter/w/71c47a/32.png) [@WillEaly](https://community.inventables.com/u/WillEaly)\
**Post date:** [August 29, 2015, 6:13pm UTC](https://community.inventables.com/t/vibration-issues-and-loud-noises/12535/1 "2015-08-29T18:13:50Z")

</div>

I’m not entirely sure what’s causing the vibration issues, but it’s LOUD. Like unbearably loud. I can be in my wood shop with the dust collector on and still hear my X-carve in the other room cutting. It’s a higher pitched grinding noise. any suggestions on where to tighten up a nut or bolt or v-wheel would be greatly appreciated, I’ve tightened everything I can think to tighten.

---

<div class="post-metadata">

**Author:** ![AllenMassey](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/allenmassey/32/84441_2.png) [@AllenMassey](https://community.inventables.com/u/AllenMassey)\
**Post date:** [August 29, 2015, 6:43pm UTC](https://community.inventables.com/t/vibration-issues-and-loud-noises/12535/2 "2015-08-29T18:43:17Z")

</div>

What spindle are you using and has always been this loud or did it just start getting louder recently?

---

<div class="post-metadata">

**Author:** ![WillEaly](https://avatars.discourse-cdn.com/v4/letter/w/71c47a/32.png) [@WillEaly](https://community.inventables.com/u/WillEaly)\
**Post date:** [August 29, 2015, 6:55pm UTC](https://community.inventables.com/t/vibration-issues-and-loud-noises/12535/3 "2015-08-29T18:55:19Z")

</div>

just recently, I’m using the basic one that comes with the 1000mm kit. The name/number is escaping me right now.

---

<div class="post-metadata">

**Author:** ![AllenMassey](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/allenmassey/32/84441_2.png) [@AllenMassey](https://community.inventables.com/u/AllenMassey)\
**Post date:** [August 29, 2015, 7:41pm UTC](https://community.inventables.com/t/vibration-issues-and-loud-noises/12535/4 "2015-08-29T19:41:08Z")

</div>

if you turn the spindle on without trying to cut anything is still making the same loud sounds? Or is it only making the loud sounds when it is cutting wood?

If it is loud without cutting then you may have a bad bearing in the spindle. Unfortunately that means you will need a new spindle.

---

<div class="post-metadata">

**Author:** ![DanBrown](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/danbrown/32/44929_2.png) [@DanBrown](https://community.inventables.com/u/DanBrown)\
**Post date:** [August 30, 2015, 7:32am UTC](https://community.inventables.com/t/vibration-issues-and-loud-noises/12535/5 "2015-08-30T07:32:08Z")

</div>

Mine died exactly that way, Will. I ended up just moving to the DeWalt, which is an improvement I can not recommend highly enough. Made it an ENTIRELY new machine, the increase in capability is absolutely absurd.
