# Vcarve and ugs

**URL:** <https://community.inventables.com/t/vcarve-and-ugs/119060>\
**Category:** Uncategorized\
**Created:** [June 13, 2021, 2:05am UTC](https://community.inventables.com/t/vcarve-and-ugs/119060 "2021-06-13T02:05:35Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![DamonWentworth](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/damonwentworth/32/75459_2.png) [@DamonWentworth](https://community.inventables.com/u/DamonWentworth)\
**Post date:** [June 13, 2021, 2:05am UTC](https://community.inventables.com/t/vcarve-and-ugs/119060/1 "2021-06-13T02:05:35Z")

</div>

hi there i just purchased a x carve upgraded from a bobs cnc i have vcarve and use ugs platform is there anything i need to do to set x carve up to use this the machine i purchased is used and they used easel with it just not sure what to do to make sure it is al good thank you for any info

---

<div class="post-metadata">

**Author:** ![MartinW.Mcclary](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/martinw.mcclary/32/63385_2.png) [@MartinW.Mcclary](https://community.inventables.com/u/MartinW.Mcclary)\
**Post date:** [June 13, 2021, 3:43pm UTC](https://community.inventables.com/t/vcarve-and-ugs/119060/2 "2021-06-13T15:43:14Z")

</div>

I use UGS all the time with my Xcarve. Run through the set up instructions to get things in ship shape.

[X-Carve Instructions: Computer Setup (inventables.com)](https://x-carve-instructions.inventables.com/1000mm/step11/)

---

<div class="post-metadata">

**Author:** ![DamonWentworth](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/damonwentworth/32/75459_2.png) [@DamonWentworth](https://community.inventables.com/u/DamonWentworth)\
**Post date:** [June 13, 2021, 9:19pm UTC](https://community.inventables.com/t/vcarve-and-ugs/119060/3 "2021-06-13T21:19:10Z")

</div>

The computer setup wants me to load easel do I have to do that

---

<div class="post-metadata">

**Author:** ![DamonWentworth](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/damonwentworth/32/75459_2.png) [@DamonWentworth](https://community.inventables.com/u/DamonWentworth)\
**Post date:** [June 13, 2021, 9:43pm UTC](https://community.inventables.com/t/vcarve-and-ugs/119060/4 "2021-06-13T21:43:13Z")

</div>

Ok I got to the point of connecting to x carve but it just sits there controller is on cable is connected nothing happens

---

<div class="post-metadata">

**Author:** ![MartinW.Mcclary](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/martinw.mcclary/32/63385_2.png) [@MartinW.Mcclary](https://community.inventables.com/u/MartinW.Mcclary)\
**Post date:** [June 13, 2021, 10:25pm UTC](https://community.inventables.com/t/vcarve-and-ugs/119060/5 "2021-06-13T22:25:59Z")

</div>

If you have an x controller, make sure the emergency stop button is pulled UP. I assume you went through the setup. Did the motors move when you hit the direction keys?

---

<div class="post-metadata">

**Author:** ![DamonWentworth](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/damonwentworth/32/75459_2.png) [@DamonWentworth](https://community.inventables.com/u/DamonWentworth)\
**Post date:** [June 13, 2021, 10:29pm UTC](https://community.inventables.com/t/vcarve-and-ugs/119060/6 "2021-06-13T22:29:06Z")

</div>

Thanks for info it was my port number and driver’s needed to be installed thank you for your help