# Troubleshooting Depth Issue **URL:** \ **Category:** Troubleshooting\ **Created:** [October 10, 2019, 8:57pm UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823 "2019-10-10T20:57:23Z")\ **Posts on this page:** 6\ **Page:** 2
**Author:** ![Joe4re](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/joe4re/32/67798_2.png) [@Joe4re](https://community.inventables.com/u/Joe4re)\ **Post date:** [October 17, 2019, 2:08pm UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823/21 "2019-10-17T14:08:42Z")
Steve, I honestly have not looked at that. I will pay attention to it when I try again this afternoon. I did check the V-wheels but will go over them again just in case. In regards to the lifting the router. If there is play would that also be the v-wheels? Thanks for all the help. Joe ---
**Author:** ![Joe4re](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/joe4re/32/67798_2.png) [@Joe4re](https://community.inventables.com/u/Joe4re)\ **Post date:** [October 17, 2019, 2:09pm UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823/22 "2019-10-17T14:09:39Z")
Dominik, Thank you for the input. i will take a look at that as well. Much appreciated, Joe ---
**Author:** ![Joe4re](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/joe4re/32/67798_2.png) [@Joe4re](https://community.inventables.com/u/Joe4re)\ **Post date:** [October 17, 2019, 8:54pm UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823/23 "2019-10-17T20:54:33Z")
Thank you to all who chimed in on this post. All your advise and assistance has been great. After working 80+ hours a week for the past 2 months. I have only had the x-carve a few months and have had little to no time to figure many of the ins and outs of it. I finally had a few hours today to work with the machine. I readjusted all 4 of the z axis v-wheels, tightened all 3 belts and did some overall fine tuning. The end result was just what I was hoping for. I have some adjusting to do on the text but am happy with the finished product. ![IMG_20191017_133345](https://yyz1.discourse-cdn.com/flex009/images/transparent.png) ![IMG_20191017_133400](https://yyz1.discourse-cdn.com/flex009/images/transparent.png) ![IMG_20191017_133354](https://yyz1.discourse-cdn.com/flex009/images/transparent.png) The cuts were clean and the surface was smooth and flat. Thanks again, Joe ---
**Author:** ![WayneHall](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/waynehall/32/84646_2.png) [@WayneHall](https://community.inventables.com/u/WayneHall)\ **Post date:** [October 17, 2019, 9:14pm UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823/24 "2019-10-17T21:14:23Z")
Big differance from the first cut.Looks good. ---
**Author:** ![SteveMoloney](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/stevemoloney/32/84542_2.png) [@SteveMoloney](https://community.inventables.com/u/SteveMoloney)\ **Post date:** [October 18, 2019, 8:46am UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823/25 "2019-10-18T08:46:44Z")
Looks good! Happy to help! As you have just found, this forum is awesome! ---
**Author:** ![Joe4re](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/joe4re/32/67798_2.png) [@Joe4re](https://community.inventables.com/u/Joe4re)\ **Post date:** [October 18, 2019, 4:30pm UTC](https://community.inventables.com/t/troubleshooting-depth-issue/78823/26 "2019-10-18T16:30:46Z")
Steve, Yes, this forum is amazing. Honestly, when I was on the fence about purchasing the x-carve this forum was one of the deciding factors in my pulling the trigger. I was a bit intimidated with the machine but saw the support and help here. [Previous page](https://community.inventables.com/t/troubleshooting-depth-issue/78823.md?page=1)