# Off center **URL:** \ **Category:** X-Carve\ **Created:** [September 21, 2021, 10:19pm UTC](https://community.inventables.com/t/off-center/122479 "2021-09-21T22:19:01Z")\ **Posts on this page:** 6\ **Page:** 1
**Author:** ![MichaelDavidBrown](https://avatars.discourse-cdn.com/v4/letter/m/e0b2c6/32.png) [@MichaelDavidBrown](https://community.inventables.com/u/MichaelDavidBrown)\ **Post date:** [September 21, 2021, 10:19pm UTC](https://community.inventables.com/t/off-center/122479/1 "2021-09-21T22:19:01Z")
I recently upgraded my x carve, I was trying to carve on a piece of material 10in wide by 7inch tall. when I started the actual carve it started carving way out of position, I have been carving with the x carve for 2 years and never had an issue, I change my dimensions of material like I always have. It goes to almost the middle of the board and start to carve, I my home position is 0,0. example would be I have the design set up to start at the x axis at 1 and the y axis at 1. the overall design is 5"x5". it will start to carve on the x axis at 4 and the y at 4 so half my design is on the board and the other half is not. I’m sure I am missing something simple, any ideas? ---
**Author:** ![WayneHall](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/waynehall/32/84646_2.png) [@WayneHall](https://community.inventables.com/u/WayneHall)\ **Post date:** [September 22, 2021, 12:06am UTC](https://community.inventables.com/t/off-center/122479/2 "2021-09-22T00:06:19Z")
Did you update your $ setting after you upgraded the machine? ---
**Author:** ![MichaelDavidBrown](https://avatars.discourse-cdn.com/v4/letter/m/e0b2c6/32.png) [@MichaelDavidBrown](https://community.inventables.com/u/MichaelDavidBrown)\ **Post date:** [September 22, 2021, 1:00am UTC](https://community.inventables.com/t/off-center/122479/3 "2021-09-22T01:00:58Z")
yes another thing I notice to is now the z axis just as I raise the bit to start it goes up about an inch. it used to go up only about about a 1/4in or so. I have used it to make a carve since the upgrade. this is a new one to me ---
**Author:** ![BrandonR\_Parker](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/brandonr_parker/32/13853_2.png) [@BrandonR\_Parker](https://community.inventables.com/u/BrandonR_Parker)\ **Post date:** [September 22, 2021, 3:06am UTC](https://community.inventables.com/t/off-center/122479/4 "2021-09-22T03:06:34Z")
As @WayneHall eluded to, I would go back and double-check the GRBL settings. It sounds like they are no longer what they should be after the upgrades you have made. {:0) Brandon Parker ---
**Author:** ![SethCNC](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/sethcnc/32/87515_2.png) [@SethCNC](https://community.inventables.com/u/SethCNC)\ **Post date:** [September 22, 2021, 4:42am UTC](https://community.inventables.com/t/off-center/122479/5 "2021-09-22T04:42:02Z")
The 25% movement could be grbl settings or dip switch setting, so if your $102 is right, check the dip switches are right. The $102 resetting during the machine profile setupwas a thing, for a while, not sure if this is still Galesburg and b that’s what you’re experiencing? [![](https://img.youtube.com/vi/W9TadmaBcNA/maxresdefault.jpg "Using Easel?? Here's WHY your CNC just crashed 💥") ](https://www.youtube.com/watch?v=W9TadmaBcNA) ---
**Author:** ![system](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/system/32/67217_2.png) [@system](https://community.inventables.com/u/system)\ **Post date:** [December 21, 2021, 4:42am UTC](https://community.inventables.com/t/off-center/122479/6 "2021-12-21T04:42:23Z")
This topic was automatically closed 90 days after the last reply. New replies are no longer allowed.