# Just a question about these lines

**URL:** <https://community.inventables.com/t/just-a-question-about-these-lines/156452>\
**Category:** Uncategorized\
**Created:** [August 17, 2024, 10:06am UTC](https://community.inventables.com/t/just-a-question-about-these-lines/156452 "2024-08-17T10:06:55Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![DouglasWhitfield](https://avatars.discourse-cdn.com/v4/letter/d/8e7dd6/32.png) [@DouglasWhitfield](https://community.inventables.com/u/DouglasWhitfield)\
**Post date:** [August 17, 2024, 10:06am UTC](https://community.inventables.com/t/just-a-question-about-these-lines/156452/1 "2024-08-17T10:06:55Z")

</div>

Never mind, I am jut stupid LOL the dotted line were the max size this particular machine will carve - I have never done anything before larger than 7 x 11 - Thanks for the help - the blue line did go away when I turned off tiling

I haven’t used my Easel Pro in quite a while. I have this set as 12" x 12" x 1" because I will be carving on a board that is 28" long x apx 7" high(live edge) x 1" thick. It will be a wall hanging coat rack.

The reason I went 12x12 is to make it easier to center my long piece on the CNC - What are the dotted lines? Can I get rid of them and how and also the dark line at 6 inches. Thanks for any help here. - hope this picture comes through.

 ![texascoat](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/2/7/2705fa66c09ecc0b85a9d9691d80b6d9bc24a4b7.jpeg)

---

<div class="post-metadata">

**Author:** ![MartinW.Mcclary](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/martinw.mcclary/32/63385_2.png) [@MartinW.Mcclary](https://community.inventables.com/u/MartinW.Mcclary)\
**Post date:** [August 17, 2024, 11:53am UTC](https://community.inventables.com/t/just-a-question-about-these-lines/156452/2 "2024-08-17T11:53:07Z")

</div>

Did you turn tiling off or is it still on? I have limited easel knowledge because I use Rhino3d but I had similar lines and they went away turning Tiling off.

---

<div class="post-metadata">

**Author:** ![DouglasWhitfield](https://avatars.discourse-cdn.com/v4/letter/d/8e7dd6/32.png) [@DouglasWhitfield](https://community.inventables.com/u/DouglasWhitfield)\
**Post date:** [August 17, 2024, 1:13pm UTC](https://community.inventables.com/t/just-a-question-about-these-lines/156452/3 "2024-08-17T13:13:46Z")

</div>

Thanks I will give it a shot - I was totally new to the CNC a year ago. Daughter and husband bought it as a gift so I am learning as I go

---

<div class="post-metadata">

**Author:** ![DouglasWhitfield](https://avatars.discourse-cdn.com/v4/letter/d/8e7dd6/32.png) [@DouglasWhitfield](https://community.inventables.com/u/DouglasWhitfield)\
**Post date:** [August 17, 2024, 1:25pm UTC](https://community.inventables.com/t/just-a-question-about-these-lines/156452/4 "2024-08-17T13:25:37Z")

</div>

I turned the tiling off and the blue line went away but the dotted one is still there - that is the size of the last piece I did but when I created this file I created a new project so I wouldn’t think that would have carried to this one - No big dead other than that is just about where I need to center my carve - I am going to put a scrap piece in and test it and then “should” be good to go - thanks

---

<div class="post-metadata">

**Author:** ![system](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/system/32/67217_2.png) [@system](https://community.inventables.com/u/system)\
**Post date:** [November 15, 2024, 1:26pm UTC](https://community.inventables.com/t/just-a-question-about-these-lines/156452/5 "2024-11-15T13:26:35Z")

</div>

Closed on November 15, 2024, 1:26pm UTC

This topic was automatically closed 90 days after the last reply. New replies are no longer allowed.