# Help Breaking Bits

**URL:** <https://community.inventables.com/t/help-breaking-bits/100765>\
**Category:** Uncategorized\
**Created:** [September 28, 2020, 7:45pm UTC](https://community.inventables.com/t/help-breaking-bits/100765 "2020-09-28T19:45:35Z")\
**Posts on this page:** 12\
**Page:** 1

<div class="post-metadata">

**Author:** ![ShawnAPerkins](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@ShawnAPerkins](https://community.inventables.com/u/ShawnAPerkins)\
**Post date:** [September 28, 2020, 7:45pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/1 "2020-09-28T19:45:35Z")

</div>

I keep breaking the 1/32 bit. The majority of the time it is sheared off in the wood, as if its not rising high enough out to move to the next cut. I have followed all the directions from the computer. I use the z probe prior to start. the settings are Plunge Rate 12in/min Depth per pass 0.015in and feed rate is 30 in/min. I have the router set on one and I’m trying to cut pine and cedar wood. I’m also taking measurements of the wood and double checking. I have had other successful carves with other bits. I have had my X carve for about a month and I have spent a lot of money on bits.

---

<div class="post-metadata">

**Author:** ![WayneHall](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/waynehall/32/84646_2.png) [@WayneHall](https://community.inventables.com/u/WayneHall)\
**Post date:** [September 28, 2020, 9:31pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/2 "2020-09-28T21:31:31Z")

</div>

Not to be pushy but a 1/32" bit is extremely fragile. I would go to a vbit and i should do what you want. I have taken the bits out and touched them wrong and they break. They are just not worth the effort.

---

<div class="post-metadata">

**Author:** ![ShawnAPerkins](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@ShawnAPerkins](https://community.inventables.com/u/ShawnAPerkins)\
**Post date:** [September 28, 2020, 10:19pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/3 "2020-09-28T22:19:18Z")

</div>

I’m trying to do military rank on a 4X4 coaster and one of the ranks will only look like its supposed to with a 1/32 according to x carve. I just broke a 1/16 cause its not clearing the wood as it moves. On the last carve I set the bit to carve at 1/8 or .12 and when I check it, it’s .21. Gong to try the Vbit.

---

<div class="post-metadata">

**Author:** ![RussellCrawford](https://avatars.discourse-cdn.com/v4/letter/r/958977/32.png) [@RussellCrawford](https://community.inventables.com/u/RussellCrawford)\
**Post date:** [September 29, 2020, 1:02am UTC](https://community.inventables.com/t/help-breaking-bits/100765/4 "2020-09-29T01:02:01Z")

</div>

Hello Shawn and welcome to the forum,  
Are you tightening the bits in the collet good? The bit shouldn’t be slipping

---

<div class="post-metadata">

**Author:** ![HaldorLonningdal](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/haldorlonningdal/32/72377_2.png) [@HaldorLonningdal](https://community.inventables.com/u/HaldorLonningdal)\
**Post date:** [September 29, 2020, 10:24am UTC](https://community.inventables.com/t/help-breaking-bits/100765/5 "2020-09-29T10:24:25Z")

</div>

> [@ShawnAPerkins](#):
>
> I keep breaking the 1/32 bit. The majority of the time it is sheared off in the wood, as if its not rising high enough out to move to the next cut.

- If your Z is loosing steps during retraction the bit will ride low and bits will break.
- If your probe offset value is slightly off the bit may ride lower than calculated and engage too much material for the first depth pass.
- 1/32" are extremely fragile and take “nothing” to break.
- 1/32" are perhaps better suited for higher RPM than the default #1 setting
- Tool length affect bit rigidity a lot, how long are the cutter length? Perhaps a shorter and more rigid one will suit your application better?

Please share an example of what you want to make, perhaps we can provide input on better tools / approaches to get you past breaking bits? 🙂

---

<div class="post-metadata">

**Author:** ![SteveMoloney](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/stevemoloney/32/84542_2.png) [@SteveMoloney](https://community.inventables.com/u/SteveMoloney)\
**Post date:** [September 29, 2020, 10:34am UTC](https://community.inventables.com/t/help-breaking-bits/100765/6 "2020-09-29T10:34:52Z")

</div>

v bit is your best option, can you share your project so we can see and give additional suggestions

---

<div class="post-metadata">

**Author:** ![ShawnAPerkins](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@ShawnAPerkins](https://community.inventables.com/u/ShawnAPerkins)\
**Post date:** [September 29, 2020, 1:21pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/7 "2020-09-29T13:21:35Z")

</div>

Yes I’m tightening it. I don’t see any slippage.

 ![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/b/c/bc653bb69ee36e9265d9ad8210046596fab0b3a6.jpeg) ![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/9/5/958acd79aebf0d489cbc2dbfdfc7753b8585f8e9.jpeg)

---

<div class="post-metadata">

**Author:** ![HaldorLonningdal](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/haldorlonningdal/32/72377_2.png) [@HaldorLonningdal](https://community.inventables.com/u/HaldorLonningdal)\
**Post date:** [September 29, 2020, 1:36pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/8 "2020-09-29T13:36:48Z")

</div>

Can you share the Easel file so we can see the intended design?

---

<div class="post-metadata">

**Author:** ![ShawnAPerkins](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@ShawnAPerkins](https://community.inventables.com/u/ShawnAPerkins)\
**Post date:** [September 29, 2020, 1:37pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/9 "2020-09-29T13:37:47Z")

</div>

![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/b/c/bc653bb69ee36e9265d9ad8210046596fab0b3a6.jpeg) ![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/9/5/958acd79aebf0d489cbc2dbfdfc7753b8585f8e9.jpeg) ![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/d/e/de9e544b6832465be0c290d18f0651769f841cdb.jpeg) ![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/f/3/f342ac349b4cc090fe80c25336fe469475e1331c.jpeg) ![image](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/d/0/d0d9c325aa8592c70438ec1a1b3a990e47d2f4b9.jpeg)

---

<div class="post-metadata">

**Author:** ![RussellCrawford](https://avatars.discourse-cdn.com/v4/letter/r/958977/32.png) [@RussellCrawford](https://community.inventables.com/u/RussellCrawford)\
**Post date:** [September 29, 2020, 3:58pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/10 "2020-09-29T15:58:58Z")

</div>

Did you stop the job before it was complete?  
Did you cut all of that using the same bit?

---

<div class="post-metadata">

**Author:** ![ShawnAPerkins](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@ShawnAPerkins](https://community.inventables.com/u/ShawnAPerkins)\
**Post date:** [September 29, 2020, 11:52pm UTC](https://community.inventables.com/t/help-breaking-bits/100765/11 "2020-09-29T23:52:07Z")

</div>

No that is three different jobs three bits, the rank was don’t with the 60 VBIT, cut to deep messed up detail. The arrowhead was cut with a 1/8 bit came out great. The one with the female was a 1/16 and yes I stopped it after it messed up the letters in the bottom. Hit the a up on the computer and it went to home and broke the bit before it cleared the wood.

---

<div class="post-metadata">

**Author:** ![RussellCrawford](https://avatars.discourse-cdn.com/v4/letter/r/958977/32.png) [@RussellCrawford](https://community.inventables.com/u/RussellCrawford)\
**Post date:** [September 30, 2020, 12:27am UTC](https://community.inventables.com/t/help-breaking-bits/100765/12 "2020-09-30T00:27:00Z")

</div>

Did you pause the job while it was running? I know if I pause on the controller and then cancel on  
the computer it will mess things up and I will have to re home when I hit carve again. Have you tried it again and were you successful?  
Maybe someone else has an idea of what is happening 🤷‍♂️  
Russell
