# First cut is 4mm deep and doc is set to .3mm

**URL:** <https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691>\
**Category:** Carvey\
**Created:** [October 6, 2018, 5:41am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691 "2018-10-06T05:41:09Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 5:41am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/1 "2018-10-06T05:41:10Z")

</div>

My first cut of my project is cutting close to 4mm on first pass and I have it set to .3mm per pass I tried to contact customer service and no reply

Please help

---

<div class="post-metadata">

**Author:** ![MechanicalGoose](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/mechanicalgoose/32/23024_2.png) [@MechanicalGoose](https://community.inventables.com/u/MechanicalGoose)\
**Post date:** [October 6, 2018, 8:41am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/2 "2018-10-06T08:41:38Z")

</div>

How did you set your initial work zero position for the Z axis?

---

<div class="post-metadata">

**Author:** ![HaldorLonningdal](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/haldorlonningdal/32/72377_2.png) [@HaldorLonningdal](https://community.inventables.com/u/HaldorLonningdal)\
**Post date:** [October 6, 2018, 9:05am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/3 "2018-10-06T09:05:08Z")

</div>

Export the gcode and post it here, there are people who can see what the machine is told to do.

Most likely you have a work flow error, or a mechanical problem.

Can you elaborate on your work flow, describing the steps you do prior to hitting Carve?

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 7:57pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/4 "2018-10-06T19:57:58Z")

</div>

first 20 lines of g-code

G90  
G21  
G28  
G21 G38.2 Z-71 F80  
G10 L20 P1 X17 Y-12.25 Z12.7  
G54  
G0 Z20  
G0 X20 Y20  
M3 S12000  
G4 P1  
G0 X75.659 Y41.618  
G1 Z-0.300 F304.8  
G1 X74.830 Y41.618 F1016.0  
G1 X74.830 Y41.368 F1016.0  
G1 X75.659 Y41.368 F1016.0  
G1 X75.659 Y41.618 F1016.0  
G1 Z-0.600 F304.8  
G1 X74.830 Y41.618 F1016.0  
G1 X74.830 Y41.368 F1016.0  
G1 X75.659 Y41.368 F1016.0  
G1 X75.659 Y41.618 F1016.0  
G1 Z-0.900 F304.8

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 7:59pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/5 "2018-10-06T19:59:34Z")

</div>

i load the material, clamp it down, load the bit, close the door, hit carve

---

<div class="post-metadata">

**Author:** ![HaldorLonningdal](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/haldorlonningdal/32/72377_2.png) [@HaldorLonningdal](https://community.inventables.com/u/HaldorLonningdal)\
**Post date:** [October 6, 2018, 8:06pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/6 "2018-10-06T20:06:50Z")

</div>

What design program do you use, post processor and sender?  
Wondering of the G28 command is intended (I dont have a Carvey)

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 8:09pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/7 "2018-10-06T20:09:37Z")

</div>

all done in easel G28 return home

---

<div class="post-metadata">

**Author:** ![MechanicalGoose](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/mechanicalgoose/32/23024_2.png) [@MechanicalGoose](https://community.inventables.com/u/MechanicalGoose)\
**Post date:** [October 6, 2018, 9:31pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/8 "2018-10-06T21:31:27Z")

</div>

Sorry, didn’t notice this was a Carvey question. The code above looks correct to me. How accurately are you measuring the thickness of your material for entering into Easel? To find the top surface of your material stock Carvey will subtract the thickness you put in from it’s known Z point after it probes the smart clamp. This is usually the culprit for situations like this. The bit could also be pulled out a bit from the spindle if it isn’t tightened appropriately.

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [October 6, 2018, 10:29pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/9 "2018-10-06T22:29:18Z")

</div>

> [@MechanicalGoose](#):
>
> How accurately are you measuring the thickness of your material for entering into Easel?

This wouldn’t matter on the Carvey. The “smart” clamp is 12.7mm above the surface of the stock, and sets the Z to match. My guess is that your stock is not entirely flat or not evenly clamped, and you’re moving too fast for the little spindle. It’s probably pulling itself down into the material or vice versa.  
Or this:

> [@MechanicalGoose](#):
>
> The bit could also be pulled out a bit from the spindle if it isn’t tightened appropriately.

My suggestion:  
Don’t clamp down tightly with the “smart” clamp, and cut your federate to 600. What material?

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 10:47pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/10 "2018-10-06T22:47:48Z")

</div>

it was acrylic so req feed rate is 1000 or so the first plunge is just as deep as the running cut

---

<div class="post-metadata">

**Author:** ![MechanicalGoose](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/mechanicalgoose/32/23024_2.png) [@MechanicalGoose](https://community.inventables.com/u/MechanicalGoose)\
**Post date:** [October 6, 2018, 10:54pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/11 "2018-10-06T22:54:07Z")

</div>

Ok cool makes sense. So the pin in the smart clamp is effectively a z-probe similar to what we use on the X-carve just built in.

Jason, do you only see this with this material/project? Do you have a scrap of some other material you could use this project on to see if you get the same results?

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [October 6, 2018, 10:54pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/12 "2018-10-06T22:54:11Z")

</div>

Are you sure the material isn’t being pulled up?  
Since it’s acrylic, it’s probably nice and flat.

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [October 6, 2018, 10:56pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/13 "2018-10-06T22:56:32Z")

</div>

> [@MechanicalGoose](#):
>
> So the pin in the smart clamp is effectively a z-probe similar to what we use on the X-carve just built in.

Exactly. G28 is the probing location on the Carvey.

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 11:06pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/14 "2018-10-06T23:06:23Z")

</div>

yeah i am sure that it is not moving

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [October 6, 2018, 11:32pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/15 "2018-10-06T23:32:19Z")

</div>

That’s gotta be a fast first pass. How thick is the acrylic?  
Do some tests before you get in touch with Inventables.  
Create a series of stepped concentric circle pockets, say .5mm through 2mm, with a DOC of .5mm and measure the depth accurately and precisely. Use a straight flute end mill if you have one.  
Watch your spindle closely… It may be loose in it’s mount.

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 6, 2018, 11:39pm UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/16 "2018-10-06T23:39:39Z")

</div>

5mm

 ![20181006_163407[1]](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/8/d/8d96cfe32fb296c4a251ce9d7b9528762bc7ef72.jpg) ![20181006_163423[1]](https://canada1.discourse-cdn.com/flex009/uploads/inventables/original/3X/d/5/d5d0efdbbc98357347da2aa714a328a45b163552.jpg) here are the plunges on 2 attempts

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [October 7, 2018, 12:08am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/17 "2018-10-07T00:08:43Z")

</div>

How are you stopping it after one pass to measure? That gcode you shared is the start of just a tiny pocket. Can you share the Easel project?

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 7, 2018, 12:16am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/18 "2018-10-07T00:16:48Z")

</div>

> **[kenzie](https://easel.inventables.com/projects/bYWHwrJKpabb3iHOEAr5iw)**
>
> by Jason Pigeon

---

<div class="post-metadata">

**Author:** ![JasonPigeon](https://avatars.discourse-cdn.com/v4/letter/j/65b543/32.png) [@JasonPigeon](https://community.inventables.com/u/JasonPigeon)\
**Post date:** [October 7, 2018, 12:20am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/19 "2018-10-07T00:20:49Z")

</div>

it broke my bit the first time and used button to kill it second time

---

<div class="post-metadata">

**Author:** ![NeilFerreri1](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/neilferreri1/32/84403_2.png) [@NeilFerreri1](https://community.inventables.com/u/NeilFerreri1)\
**Post date:** [October 7, 2018, 12:28am UTC](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691/20 "2018-10-07T00:28:18Z")

</div>

Yeah, it’s gonna mill those little slots really fast, especially with a 1/16" end mill. It might look like a plunge while it’s milling a tiny slot.  
Have you carved anything else?

[Next page](https://community.inventables.com/t/first-cut-is-4mm-deep-and-doc-is-set-to-3mm/61691.md?page=2)
