# Finished pass not the right depth

**URL:** <https://community.inventables.com/t/finished-pass-not-the-right-depth/90056>\
**Category:** Uncategorized\
**Created:** [April 17, 2020, 3:03am UTC](https://community.inventables.com/t/finished-pass-not-the-right-depth/90056 "2020-04-17T03:03:47Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![DennisLaff](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/dennislaff/32/68676_2.png) [@DennisLaff](https://community.inventables.com/u/DennisLaff)\
**Post date:** [April 17, 2020, 3:03am UTC](https://community.inventables.com/t/finished-pass-not-the-right-depth/90056/1 "2020-04-17T03:03:47Z")

</div>

I’m new to the forum just got my x carve 1 month ago ,i’ve made a few projects so far with out any problems till today roughed out project went to finish pass .025 not deep enough how do i run finish pass again and lower bit .025 using Z probe i’m a retired machinist just not to familiar with Easel software yet Thanks For Any help in advance Dennis Laff

---

<div class="post-metadata">

**Author:** ![WayneHall](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/waynehall/32/84646_2.png) [@WayneHall](https://community.inventables.com/u/WayneHall)\
**Post date:** [April 17, 2020, 3:13am UTC](https://community.inventables.com/t/finished-pass-not-the-right-depth/90056/2 "2020-04-17T03:13:09Z")

</div>

Just run it again from your same x,y,z position and make the cut .025 deeper. Then adjust the depth per pass to the full depth and it will make 1 pass and save you some time.

---

<div class="post-metadata">

**Author:** ![DennisLaff](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/dennislaff/32/68676_2.png) [@DennisLaff](https://community.inventables.com/u/DennisLaff)\
**Post date:** [April 17, 2020, 3:23am UTC](https://community.inventables.com/t/finished-pass-not-the-right-depth/90056/3 "2020-04-17T03:23:27Z")

</div>

Thanks WayneHall i’ll try it tomorrow Dennis

---

<div class="post-metadata">

**Author:** ![SteveMoloney](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/stevemoloney/32/84542_2.png) [@SteveMoloney](https://community.inventables.com/u/SteveMoloney)\
**Post date:** [April 17, 2020, 9:07am UTC](https://community.inventables.com/t/finished-pass-not-the-right-depth/90056/4 "2020-04-17T09:07:03Z")

</div>

I use .03 with a spoil board of course. On my monograms in PVC I typically rerun the entire project at full depth one pass, really cleans up all the edges nicely.

---

<div class="post-metadata">

**Author:** ![DennisLaff](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/dennislaff/32/68676_2.png) [@DennisLaff](https://community.inventables.com/u/DennisLaff)\
**Post date:** [April 18, 2020, 11:45pm UTC](https://community.inventables.com/t/finished-pass-not-the-right-depth/90056/5 "2020-04-18T23:45:39Z")

</div>

Thanks WayneHall And SteveMoloney got it done