# \[Challenge\] Beer can holder for workshop

**URL:** https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381
**Category:** Projects
**Created:** [September 19, 2015, 7:11pm UTC](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381 "2015-09-19T19:11:25Z")
**Posts on this page:** 5
**Page:** 3

<div class="post-metadata">

### Author: ![JohnSheak](https://avatars.discourse-cdn.com/v4/letter/j/9f8e36/32.png) [@JohnSheak](https://community.inventables.com/u/JohnSheak)
#### Post date: [September 24, 2015, 11:13pm UTC](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381/48 "2015-09-24T23:13:08Z")

</div>

terry, I don’t know where you got that… but couldn’t you use this instead…  
 ![](https://cdck-file-uploads-canada1.s3.dualstack.ca-central-1.amazonaws.com/flex009/uploads/inventables/original/2X/7/758a8d9e3db6786707cc839af49a4a64c0df2ca3.png)  
I am sure you could get a sponsored bounty from inventables if you figure how to mount it to provent shaking… sure it would be spill proof.

---

<div class="post-metadata">

### Author: ![Tarry\_Brindle](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/tarry_brindle/32/32229_2.png) [@Tarry\_Brindle](https://community.inventables.com/u/Tarry_Brindle)
#### Post date: [September 25, 2015, 2:00pm UTC](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381/49 "2015-09-25T14:00:44Z")

</div>

Using that didn’t even cross my mind!

---

<div class="post-metadata">

### Author: ![RobertA\_Rieke](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/roberta_rieke/32/32723_2.png) [@RobertA\_Rieke](https://community.inventables.com/u/RobertA_Rieke)
#### Post date: [September 27, 2015, 6:09pm UTC](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381/50 "2015-09-27T18:09:48Z")

</div>

@JohnSheak I just checked, and my 611 mount is about 1/8" larger in diameter than my Pepsi cans. It wouldn’t be hard to put a little hinged top on it that is attached to a little latch down below that simultaneously holds the can and shuts the lid. I think you’re on to something… 😄

---

<div class="post-metadata">

### Author: ![JohnSheak](https://avatars.discourse-cdn.com/v4/letter/j/9f8e36/32.png) [@JohnSheak](https://community.inventables.com/u/JohnSheak)
#### Post date: [September 28, 2015, 4:08am UTC](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381/51 "2015-09-28T04:08:08Z")

</div>

some makerslide… gt2 belt and a nema 17 moter

if your in the garage… makeslide though ahole in wall to kitchen… at the end next to the fridge a limit switch that rings a bell… wife places beer in mount… bamm  
or  
If you are in a basement… x-carve beer dumbwaiter…

---

<div class="post-metadata">

### Author: ![JkWestphal](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/jkwestphal/32/53751_2.png) [@JkWestphal](https://community.inventables.com/u/JkWestphal)
#### Post date: [September 28, 2015, 12:24pm UTC](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381/53 "2015-09-28T12:24:33Z")

</div>

Better yet, getting wifee off of facecrook long enough to get up and place said beer into holder…

[Previous page](https://community.inventables.com/t/challenge-beer-can-holder-for-workshop/13381.md?page=2)