# $102 going back to default

**URL:** <https://community.inventables.com/t/102-going-back-to-default/51758>\
**Category:** Uncategorized\
**Created:** [March 2, 2018, 2:02pm UTC](https://community.inventables.com/t/102-going-back-to-default/51758 "2018-03-02T14:02:42Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![PatrickDunne](https://avatars.discourse-cdn.com/v4/letter/p/a3d4f5/32.png) [@PatrickDunne](https://community.inventables.com/u/PatrickDunne)\
**Post date:** [March 2, 2018, 2:02pm UTC](https://community.inventables.com/t/102-going-back-to-default/51758/1 "2018-03-02T14:02:42Z")

</div>

I have been searching the forum for an answer to this, I can’t get $102=377,952 to keep this new setting I input, it keeps going back to default, (it is set at this because I have a linear Z - rail) and was working fine, and some others as well $24 and $25 and $20 $21 and $22, I did click on refresh, (the 2 arrows in a circle), and restarted the X-controller, but nothing works, has anyone else had this problem

---

<div class="post-metadata">

**Author:** ![HaldorLonningdal](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/haldorlonningdal/32/72377_2.png) [@HaldorLonningdal](https://community.inventables.com/u/HaldorLonningdal)\
**Post date:** [March 2, 2018, 2:12pm UTC](https://community.inventables.com/t/102-going-back-to-default/51758/2 "2018-03-02T14:12:54Z")

</div>

There is no reason for the controller to reset its GRBL-settings, unless told to do so.

If you edit the $102 value in Easel Machine Inspector, and after that type $$ do the correct value appear?  
If yes - if you turn power off/on on the controller do the same value appear again when you $$?

---

<div class="post-metadata">

**Author:** ![PatrickDunne](https://avatars.discourse-cdn.com/v4/letter/p/a3d4f5/32.png) [@PatrickDunne](https://community.inventables.com/u/PatrickDunne)\
**Post date:** [March 2, 2018, 2:53pm UTC](https://community.inventables.com/t/102-going-back-to-default/51758/3 "2018-03-02T14:53:18Z")

</div>

Yes, In Easel Machine Inspector the correct value appears after $$ check and after a reboot of the X-controller, I am learning to use Picsender so after a while on there I go back to Easel and check the $102 again, and it has gone back to default, I am not touching any GRBL settings in Picsender

---

<div class="post-metadata">

**Author:** ![LarryM](https://yyz1.discourse-cdn.com/flex009/user_avatar/community.inventables.com/larrym/32/51450_2.png) [@LarryM](https://community.inventables.com/u/LarryM)\
**Post date:** [March 2, 2018, 2:58pm UTC](https://community.inventables.com/t/102-going-back-to-default/51758/4 "2018-03-02T14:58:31Z")

</div>

If I remember correctly you use PicsSender.

Read through this[article](https://community.inventables.com/t/picsender-g-code-sender/34307/101) and it should make things a little clearer. The screen snapshots are from version 2.5.7, but the information is the same for version 2.8.0.

---

<div class="post-metadata">

**Author:** ![PatrickDunne](https://avatars.discourse-cdn.com/v4/letter/p/a3d4f5/32.png) [@PatrickDunne](https://community.inventables.com/u/PatrickDunne)\
**Post date:** [March 6, 2018, 7:25am UTC](https://community.inventables.com/t/102-going-back-to-default/51758/5 "2018-03-06T07:25:45Z")

</div>

Thank’s Larry  
I have read through that and the GRBL settings seem to have stayed fixed in Picsender now, I think my Easel is not working properly, I can’t use the probe in there either (all the set up pages do not load) and it works fine in Picsender, so I don’t really need Easel anymore